Prototype Boards Arrived

The new DG5 emulator board (with Atmel 328p on board) arrived Saturday, and I put one together today. It looks good, the only issues were 2 caps were not labeled (silk-screened) on the board. Worked the first time.

Since there isn’t an Arduino board involved, there us no USB port to program the micro-controller. Instead, there is a FTDI header that allows you to plug in a USB to TTL converter – I am using one from Adafruit called the FTDI Friend. It includes a reset line wired to RTS, which allows the Arduino IDE to be able to program it. The board is wired to allow this to plug directly in for programming, other FTDI boards should work but might need a cross connecting wire to get the signals (TX/RX/GND/RESET) going to the right places. And the Atmel processor will need an Arduino bootloader for this to work anyway. There are a couple of ways to handle this.

  1. Buy (or use existing) Arduino with a socketed, 28pin Atmel 328p like the UNO to program the chip.
  2. Buy a pre-programmed 328p chip from me with either the LED, LCD, or NIXIE code pre-loaded.

If you already have an Arduino UNO or similar, you can program the chip, remove it and install it in this board. If you buy the chip from me, you don’t need an Arduino. You don’t need the FTDI board either, but you won’t be able to connect to it to enable debugging if necessary, or be able to update the code in the future.

Some pics:

The populated board, version 2.0.2
The new RCA triple ganged jack
With the FTDI adapter plugged in
Board attached to LED module

I corrected the missing silkscreen labels, and added a solderable pad to the 5V line on the FTDI header. You don’t want the 5V from the FTDI board mixing with the 5V on the board – the linear regulator provides nice, clean power, and when the 5V from the FTDI board was connected, the displayed frequency jumped around. As soon as I disconnected the 5V from the FTDI board, it wen’t back to smooth operation. The solderable pad will allow you to bring 5V to this pin – I will be trying a FTDI/Bluetooth board that will need power in the future.

I am thinking about kitting (include all parts except case/chassis) up a couple of these boards with the parts I have on hand, I’ll have to add up the costs and come up with a price. If there is a lot of interest in having it kitted, I’ll see what I can do. I am not trying to run a business here, and I don’t want to get sucked into a huge time waster, but this is a fun project and I am willing to make it a little easier to get off the ground. Let me know your thoughts in the comments!

Lastly, I have the one built prototype board, and have 2 more PCBs. I might build them, and put them on eBay to see what happens, no chassis, just the populated and working board as seen above. I’ll make a post here if I do!

2 thoughts on “Prototype Boards Arrived

  1. Russell Flagg

    Good day Steve,
    Great news—-very keen to purchase complete kit for the LED version of the DG5 Emulator. I have the original Kenwood DG5 which has defied all attempts to get it working! So my intention is to place your LED unit in the DG5 enclosure. You may recall I bought two of your original boards and using the Arduino UNO,
    one of which is connected, ( the LCD version) to my TS 520S. I am 83 years old, my hands not cooperating as they should and sourcing components here in South Africa is proving very difficult.

    Looking forward to your response, regards, Russell. ZS2AHF

    Reply
  2. Matt

    certainly am interested in a kit here also.

    I have a TS-520 with a home brew adapter interface to allow use of the DG5 display

    Matt, AF5XF

    Reply

Leave a Reply to Matt Cancel reply

Your email address will not be published.

This site uses Akismet to reduce spam. Learn how your comment data is processed.